Optional Interfaces and I/O for Routers



  • General Description

  • Installation

  • Ordering Codes

  • General Description

    • Most Conel routers and modems offer one or more positions for optional interfaces. Thanks to this you may customize the hardware interface according to the relevant application. This modular design lets you change interfaces in the future, or add an interface that is not currently supported. Available standard interfaces:

    • Ethernet 10/100

      • Basic surge protection
      • Supported devices: all v2 routers except UR5i v2 Libratum, UR5i, XR5i
      • Order code: XC-ETH
      • Download: Manual for XC-ETH (184 kB, PDF)
    • R232

      • Basic surge protection
      • Supported devices: all v2 routers except UR5i v2 Libratum, ER75i, UR5, UR5i, XR5i, CGU04i, CDX800, CDE7
      • Order code: XC-232
      • Download: Manual for XC-RS232 (370 kB, PDF)
    • RS485 / RS422

      • RS485 or RS422 – may be selected with switches on the board.
      • Option to use galvanic (electric) separation using switches on the board
      • Basic surge protection
      • Supported devices: all v2 routers except UR5i v2 Libratum, ER75i, UR5, UR5i, XR5i, CGU04i, CDX800, CDE7
      • Order code: XC-485/422
      • Download: Manual for XC-RS485-422 (222 kB, PDF)
    • M-BUS Master

      • M-Bus master up to 30 M-Bus slave device
      • Permanent protection against bus shortcut
      • Possibility of galvanic separation through the use of external power source
      • Supported devices: all v2 routers except UR5i v2 Libratum, ER75i, UR5, UR5i, XR5i, CGU04i, CDX800, CDE7
      • Order code: XC-M-BUS
      • Download: Manual for XC-MBUS (158 kB, PDF)
    • I/O module CNT

      • 4 binary inputs, of which up to 2 inputs may be counter inputs
      • 2 analogue inputs 4-20 mA
      • 1 binary output
      • Supported devices: all v2 routers except UR5i v2 Libratum, ER75i, UR5, UR5i, XR5i, CGU04i, CDX800
      • Order code: XC-CNT
      • Download: Manual for XC-CNT (301 kB, PDF)
    • WiFi

      • The expansion port WiFi is created as an addition to the router desk which allows for the use of a wireless interface in Conel v2 routers.
      • WiFi module supports AP (Access Point) function. This module allows you to scan the neighboring networks.
      • Expansion port WiFi supports these standards: 802.11b, 802.11g, 802.11n
      • Expansion port WiFi supports the following types of security: Shared, WPA-PSK, WPA2-PSK
      • Expansion port WiFi supports the following types of authentication: 64/128 WEP, TKIP, AES
      • Wi-Fi module is supplied exclusively to FULL version routers. Installation is carried out in our production department.
      • Supported devices: all v2 routers
      • Order code: XC-WiFi
      • Download: Manual for XC-WIFI (415 kB, PDF)
    • SDH

      • Expansion port SDH is created as an addition to the router desk that allows routers to use a SD card as a USB flash drive or as an internal memory that extends the capacity of the internal memory of your router.
      • Expansion port SDH can be used in all v2 routers with the available PORT2. Therefore it is designed for routers in a version known as FULL.
      • Supported devices: all v2 routers except UR5i v2 Libratum
      • Order code: XC-SD
      • Download: Manual for XC-SD (1 959 kB, PDF)
    • Switch

      • Internal switch (expansion port SWITCH) is created as an addition to the router desk.
      • With this device LAN ports of the router act as if this router was a typical switch device.
      • Which means that the router with an internal switch desk reads the ethernet frames (a data packets on an ethernet link) from any port and transmits them on other ports.
      • Each port on this device can transmit frames independently from every other port.
      • Supported devices: all v2 routers except UR5i v2 Libratum
      • Order code: XC-SW
      • Download: Manual for XC-SW (1 140 kB, PDF)

     

    We are preparing futher optional modules: Wireless M-Bus ...

Talk to us about your cellular project